DIN 71802 form CS

Designation	d1	d2 6g/6H**	a ±0,3	d3 ±0,5	d4 ±0,5	d6 h14	e min.	h2 ±0,5	l2 ±0,3	l3 ±0,3	r max.	*sw h14	*sw1 h14	α° ≈	weight (Kg) ≈
CS 8 M5	8	M5	22	8	12,8	8	10,2	0,65	10,2	9	0,3	7	7	10	0,015
CS10 M6	10	M6	25	10	14,8	10	11,5	0,65	12,5	11	0,3	8	8	15	0,025
CS13 M8	13	M8	30	13	19,3	13	14,0	1,15	16,5	13	0,5	11	11	15	0,053
CS16 M10	16	M10	35	16	24,0	16	16	1,15	20,0	16	0,5	13	13	15	0,104
CS16 M12	16	M12	35	16	24,0	16	16	1,15	20,0	16	0,5	13	-	15	0,150
CS19 M14x1,5	19	M14x1,5	45	22	30,0	19	21,5	0,50	28,0	20	0,8	16	-	15	0,221
CS19 M14x2	19	M14	45	22	30,0	19	21,5	0,50	28,0	20	0,8	16	-	15	0,221
CS19 M16	19	M16	45	22	30,0	19	21,5	0,5	28,0	20	0,8	16	-	15	0,221

Attached Documents

Technical data

Download Product Table in Excel

Download technical drawings in DWG

Download technical drawings in DXF

Download technical drawings in GIF

Look at the packaging of this product

Series
C

DIN 71802 form C

Designation	d1	d2 6g/6H**	a ±0,3	d3 ±0,5	d4 ±0,5	d6 h14	e min.	h2 ±0,5	l2 ±0,3	l3 ±0,3	r max.	*sw h14	*sw1 h14	α° ≈	weight (Kg) ≈
C 8 M5	8	M5	22	8	12,8	8	10,2	0,65	10,2	9	0,3	7	7	10	0,015
C10 M6	10	M6	25	10	14,8	10	11,5	0,70	12,5	11	0,3	8	8	15	0,025
C13 M8	13	M8	30	13	19,3	13	14,0	1,15	16,5	13	0,5	11	11	15	0,053
C16 M10	16	M10	35	16	24,0	16	16	1,15	20,0	16	0,5	13	13	15	0,104
C16 M12	16	M12	35	16	24,0	16	16	1,15	20,0	16	0,5	13	-	15	0,150
C19 M14x1,5	19	M14x1,5	45	22	30,0	19	21,5	0,50	28,0	20	0,8	16	-	15	0,221
C19 M14x2	19	M14x2	45	22	30,0	19	21,5	0,50	28,0	20	0,8	16	-	15	0,221
C19 M16	19	M16	45	22	30,0	19	21,5	0,5	28,0	20	0,8	16	-	15	0,221

Attached Documents

Technical data

Download Product Table in Excel

Download technical drawings in DWG

Download technical drawings in DXF

Download technical drawings in GIF

Look at the packaging of this product

Notes

* Spanner flats
**tolerances d2: ball stud 6g-threaded hole 6H

For left - hand thread add "LH" (ex. CS16 M10 LH or C16 M10 LH)
Material:
Ball stud: carbon steel with 60 daN/mm2 resistance to tensile stress and inner ring hardened on the surface with a ≥ 52 HRC hardness
Ball socket: steel 11SMnPb30 with a 50 daN/mm² resistance to tensile stress (1.0718)
Internal snap ring "R": steel for springs C98 UNI EN 10270-1 DH
Safety clip "S": steel for springs C98 UNI EN 10270-1 DH
Surface protection:
-Zinc plating according to EN ISO 4042, Fe/Zn 8c...
-Chromate treatment (passivation) example: type A please add 1A (ex.:CS 10 M6 1A)
-surface treatment table
Tolerances: the dimensional tolerances shown in the table make reference to zinc plated products.